Difference between revisions of "Template:FLYSWATTER2 BEAGLEBONE CONNECT"

From eLinux.org
Jump to: navigation, search
(removing adapter bits, as it's not needed for the bone)
 
(8 intermediate revisions by the same user not shown)
Line 1: Line 1:
 
=Connecting the Flyswatter2 and the BeagleBone=
 
=Connecting the Flyswatter2 and the BeagleBone=
  
 +
==Requirements==
 
To hook up the Flyswatter2 and the BeagleBone, you will need:
 
To hook up the Flyswatter2 and the BeagleBone, you will need:
  
 
*[[Installation of the Alternative JTAG Header on the BeagleBone]]
 
*[[Installation of the Alternative JTAG Header on the BeagleBone]]
 
*20-pin JTAG Ribbon Cable
 
*20-pin JTAG Ribbon Cable
 +
*ARM20 to CTI20 Adapter
 
*USB Mini-B Device Cable
 
*USB Mini-B Device Cable
 
*5V1A Power Cable
 
*5V1A Power Cable
  
==Connect the JTAG Adapter Board to the Flyswatter2.==
+
==Connect the 20 Pin Ribbon Cable to the Flyswatter2.==
[[File:Fs2_ti_adapter.png|left]] Connect the 20-pin end of the adapter board to the Flyswatter2's JTAG interface.
+
[[File:fs2_20pin_ribbon.jpg|left|500px]] Connect one end of the 20-pin end ribbon cable to the Flyswatter2's JTAG interface.
 
<br style="clear:both;" />
 
<br style="clear:both;" />
==Connect the 14-pin Ribbon Cable to the JTAG Adapter Board.==
+
 
[[File:Fs2_ti_jtag.png|left]] Your cable most likely has a notch on the head to force it into the correct position. If it doesn't, align Pin 1 on the ribbon cable with the side of the board opposite the EMU pins. (In the picture, Pin 1 is marked by the red stripe on the cable.)
+
==Connect the 20-pin Ribbon Cable to the ARM20CTI20 Adapter Board.==
 +
[[File:fs2_bone_ribbon_adapter.jpg|left|500px]] Connect the other end of the 20 pin ribbon cable into the ARM20CTI20 adapter.  Your cable most likely has a raised nub on the head to force it into the correct position which matches a notch on the adapter. If it doesn't, align Pin 1 on the ribbon cable (marked with a red stripe) with the pin marked as 1 on the adapter.
 
<br style="clear:both;" />
 
<br style="clear:both;" />
==Connect the 10-pin Ribbon Cable to the RS-232 Adapter Board.==
+
 
[[File:Fs2_jtag14serial10.png]]
+
==Connect the 20-pin ARM20CTI20 adapter to to BeagleBone.==
<br style="clear:both;" />
+
[[File:fs2_bone_adapter.jpg|left|500px]] Next, connect the ARM20CTI20 adapter connected to the ribbon cable to the 20 pin connector that has been added to the underside of the BeagleBone.
==Connect the Other End of the Ribbon Cable to the Beagleboard XM.==
 
[[File:Fs2_beaglexm_jtag.png|left]] Be sure to align the ribbon cable correctly. Pin 1 on the Beagleboard XM is the pin closest to the center of the board.
 
 
<br style="clear:both;" />
 
<br style="clear:both;" />
 +
 
==Plug in the Serial Cable.==
 
==Plug in the Serial Cable.==
 
[[File:Fs2_beaglexm_bothcables.png|left]] Connect the Flyswatter2 and the Beagleboard XM with the RS-232 serial cable.
 
[[File:Fs2_beaglexm_bothcables.png|left]] Connect the Flyswatter2 and the Beagleboard XM with the RS-232 serial cable.

Latest revision as of 14:01, 10 April 2013

Connecting the Flyswatter2 and the BeagleBone

Requirements

To hook up the Flyswatter2 and the BeagleBone, you will need:

Connect the 20 Pin Ribbon Cable to the Flyswatter2.

Fs2 20pin ribbon.jpg

Connect one end of the 20-pin end ribbon cable to the Flyswatter2's JTAG interface.


Connect the 20-pin Ribbon Cable to the ARM20CTI20 Adapter Board.

Fs2 bone ribbon adapter.jpg

Connect the other end of the 20 pin ribbon cable into the ARM20CTI20 adapter. Your cable most likely has a raised nub on the head to force it into the correct position which matches a notch on the adapter. If it doesn't, align Pin 1 on the ribbon cable (marked with a red stripe) with the pin marked as 1 on the adapter.


Connect the 20-pin ARM20CTI20 adapter to to BeagleBone.

Fs2 bone adapter.jpg

Next, connect the ARM20CTI20 adapter connected to the ribbon cable to the 20 pin connector that has been added to the underside of the BeagleBone.


Plug in the Serial Cable.

Fs2 beaglexm bothcables.png

Connect the Flyswatter2 and the Beagleboard XM with the RS-232 serial cable.


Connect the USB cable to the Flyswatter2.

Fs2 beaglexm usb.png

Find the USB cable that comes with the Flyswatter2. Connect the B end (the square end, not the flat end) to the Flyswatter2.


Connect the Power Cable to the Beagleboard XM.

Fs2 beaglexm power.png

The Beagleboard XM's power adapter is next to the serial port.


Plug the Power Adapter into a Wall Outlet.

The green power LED on the Beagleboard XM should come on and remain on.

Plug the USB Cable into your PC.

The green power LED on the Flyswatter2 should come on and remain on.