Can't Modify U-Boot Environment Variables on Updated Firmware

Jump to: navigation, search

I am trying to get up and running with the R-Car H3 Starter Kit Premier Board (h3ulcb). I first followed the instructions here http://elinux.org/R-Car/Boards/Yocto-Gen3 to build Yocto 2.19 for the board. When I attempted to run the built Yocto image on the board (both via tftp and via microSD), I received a kernel panic message. The limited resources on the internet (i.e., the other posts on this wiki) indicated this could likely be resolved by updating the firmware. I then followed the instructions here http://elinux.org/R-Car/Boards/H3SK#Flashing_firmware to update the firmware on the board. Now when I turn the board on, I cannot get to the stage where the option of cancelling autoboot (as shown in examples in the links given). I am therefore not able to change U-Boot's environment variables to specify the Image file to boot. It seems that U-Boot is perhaps not loading at all. Any help would be greatly appreciated!

Output of boot sequence is below:

user@user-linux:~$ sudo picocom -b 115200 --send-cmd "ascii-xfr -vvs" /dev/ttyUSB0

[sudo] password for user:

picocom v1.7

port is : /dev/ttyUSB0

flowcontrol : none

baudrate is : 115200

parity is : none

databits are : 8

escape is : C-a

local echo is : no

noinit is : no

noreset is : no

nolock is : no

send_cmd is : ascii-xfr -vvs

receive_cmd is : rz -vv

imap is :

omap is :

emap is : crcrlf,delbs,

Terminal ready

[ 0.000194] NOTICE: BL2: R-Car Gen3 Initial Program Loader(CA57) Rev.1.0.14

[ 0.005761] NOTICE: BL2: PRR is R-Car H3 Ver2.0

[ 0.010335] NOTICE: BL2: Board is unknown Rev0.0

[ 0.015006] NOTICE: BL2: Boot device is HyperFlash(80MHz)

[ 0.020445] NOTICE: BL2: LCM state is CM

[ 0.024423] NOTICE: BL2: AVS setting succeeded. DVFS_SetVID=0x52

[ 0.030611] NOTICE: BL2: DDR3200(rev.0.22)NOTICE: [COLD_BOOT]NOTICE: ..0

[ 0.091270] NOTICE: BL2: DRAM Split is 4ch

[ 0.095155] NOTICE: BL2: QoS is default setting(rev.0.14)

[ 0.100655] NOTICE: BL2: Lossy Decomp areas

[ 0.104832] NOTICE: Entry 0: DCMPAREACRAx:0x80000540 DCMPAREACRBx:0x570

[ 0.111917] NOTICE: Entry 1: DCMPAREACRAx:0x40000000 DCMPAREACRBx:0x0

[ 0.118829] NOTICE: Entry 2: DCMPAREACRAx:0x20000000 DCMPAREACRBx:0x0

[ 0.125743] NOTICE: BL2: v1.3(release):4eef9a2

[ 0.130233] NOTICE: BL2: Built : 17:35:56, Jul 13 2017

[ 0.135420] NOTICE: BL2: Normal boot

[ 0.139062] NOTICE: BL2: dst=0xe6320190 src=0x8180000 len=512(0x200)

[ 0.145608] NOTICE: BL2: dst=0x43f00000 src=0x8180400 len=6144(0x1800)

[ 0.152070] NOTICE: BL2: dst=0x44000000 src=0x81c0000 len=65536(0x10000)

[ 0.159295] NOTICE: BL2: dst=0x44100000 src=0x8200000 len=524288(0x80000)

[ 0.169775] NOTICE: BL2: dst=0x50000000 src=0x8640000 len=1048576(0x100000)

05:25, 17 July 2017

I'm not sure if the Renesas engineers are watching these pages to handle support requests. I think you would be better served by asking the question on their board mailing list. See http://elinux.org/R-Car#R-Car_Community.

15:13, 17 July 2017

You do not have permission to edit this page, for the following reasons:

  • The action you have requested is limited to users in the group: Users.
  • You must confirm your email address before editing pages. Please set and validate your email address through your user preferences.

You can view and copy the source of this page.

Return to Thread:Talk:R-Car/Boards/Yocto-Gen3/Can't Modify U-Boot Environment Variables on Updated Firmware/reply (2).

I have the same h3ulcb board(RTP0RC77951SKBX010SA00) as you. I updated the loader but it started normally.

[    0.000194] NOTICE:  BL2: R-Car Gen3 Initial Program Loader(CA57) Rev.1.0.14
[    0.005761] NOTICE:  BL2: PRR is R-Car H3 Ver2.0
[    0.010335] NOTICE:  BL2: Board is unknown Rev0.0
[    0.015006] NOTICE:  BL2: Boot device is HyperFlash(80MHz)
[    0.020445] NOTICE:  BL2: LCM state is CM
[    0.024423] NOTICE:  BL2: AVS setting succeeded. DVFS_SetVID=0x52
[    0.030611] NOTICE:  BL2: DDR3200(rev.0.22)NOTICE:  [COLD_BOOT]NOTICE:  ..0
[    0.091235] NOTICE:  BL2: DRAM Split is 4ch
[    0.095121] NOTICE:  BL2: QoS is default setting(rev.0.14)
[    0.100621] NOTICE:  BL2: Lossy Decomp areas
[    0.104798] NOTICE:       Entry 0: DCMPAREACRAx:0x80000540 DCMPAREACRBx:0x570
[    0.111883] NOTICE:       Entry 1: DCMPAREACRAx:0x40000000 DCMPAREACRBx:0x0
[    0.118795] NOTICE:       Entry 2: DCMPAREACRAx:0x20000000 DCMPAREACRBx:0x0
[    0.125709] NOTICE:  BL2: v1.3(release):4eef9a2
[    0.130199] NOTICE:  BL2: Built : 10:20:37, Jul 19 2017
[    0.135386] NOTICE:  BL2: Normal boot
[    0.139028] NOTICE:  BL2: dst=0xe6320190 src=0x8180000 len=512(0x200)
[    0.145574] NOTICE:  BL2: dst=0x43f00000 src=0x8180400 len=6144(0x1800)
[    0.152037] NOTICE:  BL2: dst=0x44000000 src=0x81c0000 len=65536(0x10000)
[    0.159261] NOTICE:  BL2: dst=0x44100000 src=0x8200000 len=524288(0x80000)
[    0.169741] NOTICE:  BL2: dst=0x50000000 src=0x8640000 len=1048576(0x100000)


U-Boot 2015.04 (Jul 19 2017 - 10:20:39)

CPU: Renesas Electronics R8A7795 rev 2.0
Board: H3ULCB
I2C:   ready
DRAM:  3.9 GiB
MMC:   sh-sdhi: 0, sh-sdhi: 1
In:    serial
Out:   serial
Err:   serial
Net:   ravb
Hit any key to stop autoboot:  0
=>

However, the following are different.

[    0.100623] NOTICE:  BL2: Lossy Decomp areas
[    0.104798] NOTICE:       Entry 0: DCMPAREACRAx:0x80000540 DCMPAREACRBx:0x570
(snip)

It seems that you changed something. At first, could you build according to procedure of elinux?

Ygohda (talk)17:31, 18 July 2017

I'm sorry. The log was completely the same halfway. Have you updated all the files?

- bootparam_sa0.srec
- bl2-h3ulcb.srec
- cert_header_sa6.srec
- bl31-h3ulcb.srec
- tee-h3ulcb.srec
- u-boot-elf.srec
Ygohda (talk)17:50, 18 July 2017

Yes. One thing that wasn't clear to me was where to actually get those files. I've been using the ones that are found in ~/tmp/deploy/images/h3ulcb/ after building yocto. Assuming that's the correct path, I'm going to try rebuilding yocto in case I messed something up in that process.

One possible indication of what the issue is: I looked through the Renesas Device Manual https://www.renesas.com/en-us/doc/products/rcar/R-Car_StarterKit_Gen3_H3_M3_DEV_Rev.053.pdf to find a solution and found that in the section on booting the addresses the board boots from are slightly different from those on the e-linux wiki (looking at page 238 in particular). I'm a machine learning guy by trade and my architecture knowledge is rather scant comparatively so maybe this is nothing/not what I thought it means.

23:10, 18 July 2017

Yes, /tmp/deploy/images/h3ulcb is correct path. Please refer to the No13 of http://elinux.org/R-Car/Boards/Yocto-Gen3#Building_the_BSP_for_Renesas_H3ULCB.2C_M3ULCB.

All updating methods are described below. http://elinux.org/R-Car/Boards/H3SK#Flashing_firmware Could you try again?

If "u-boot" still doesn't start up please attach the log when flashing the firmware.

Ygohda (talk)03:03, 21 July 2017

Rebuilding the whole thing from scratch worked. Something must have gone wrong in the initial build because the .dtb file sizes between the two builds were off by a few hundred bytes.

22:38, 22 July 2017