Firmware update hangs
The highlighted comment was created in this revision.
I got a new WS1.1 Premier starter kit, tried to build 2.19.0 but the kernel was crashing.
Tried to upgrade the firmware, but it failed to download bl2 srec. Now, it is not even booting into u-boot.
I tried downloading the firmware from windows PC (Teraterm) and Linux (minicom), boot params is getting programmed. I can't program none of the other firmware as given in the instructions.
Either it hangs after sending the file (bl2, bl32, cert), or over size error (uboot)
Any inputs to recover the board is welcome.
Address of bl2 has been chenged from Yocto v2.17.0. Please check the following page. http://elinux.org/R-Car/Boards/H3SK#Flashing_firmware
yeah, following the exact instruction in your link. After downloading the bl2 the mini monitor is stuck.
I see that the board can boot into SCIF download, is it possible recover the board by this route?
I've attached the my log.
H3 SAMPLE LOADER V1.16 2016.10.24
CPU : AArch64 CA57
DRAM : LPDDR4 DDR3200 DEVICE: QSPI Flash(S25FS128) at 40MHz DMA
BOOT : Normal Boot
Backup: DDR Cold Boot
jump to 0xE6330000
H3 MiniMonitor V0.23 2016.10.24
Work Memory SystemRAM (H'E6328000-H'E632FFFF)
>
>
>xls2
===== Qspi/HyperFlash writing of Gen3 Board Command =============
Load Program to Spiflash
Writes to any of SPI address.
Please select,FlashMemory.
1 : QspiFlash (U5 : S25FS128S)
2 : QspiFlash Board (CN2: S25FL512S)
3 : HyperFlash (SiP internal)
Select (1-3)>3
READ ID OK.
Program Top Address & Qspi/HyperFlash Save Address
===== Please Input Program Top Address ============
Please Input : H'e6304000
===== Please Input Qspi/HyperFlash Save Address ===
Please Input : H'40000
Work RAM(H'50000000-H'53FFFFFF) Clear....
please send ! ('.' & CR stop load)
H'00040000-0007FFFF Erasing..Erase Completed
SAVE SPI-FLASH....... complete!
======= Qspi/HyperFlash Save Information =================
SpiFlashMemory Stat Address : H'00040000
SpiFlashMemory End Address : H'0005B03B
===========================================================
>
If you don't solve it please attach your log.
Issue is not yet resolved, please see log below.
H3 SAMPLE LOADER V1.17 2016.11.08
CPU : AArch64 CA57 DRAM : LPDDR4 DDR3200 DEVICE: QSPI Flash(S25FS128) at 40MHz DMA BOOT : Normal Boot Backup: DDR Cold Boot
jump to 0xE6330000
H3 MiniMonitor V0.24 2016.11.08
Work Memory SystemRAM (H'E6328000-H'E632FFFF)
>xls2
Contents
Qspi/HyperFlash writing of Gen3 Board Command ========[edit]
Load Program to Spiflash Writes to any of SPI address. Please select,FlashMemory.
1 : QspiFlash (U5 : S25FS128S) 2 : QspiFlash Board (CN2: S25FL512S) 3 : HyperFlash (SiP internal) Select (1-3)>3 READ ID OK.
Program Top Address & Qspi/HyperFlash Save Address
Please Input Program Top Address =======[edit]
Please Input : H'e6320000
== Please Input Qspi/HyperFlash Save Address[edit]
Please Input : H'0
Work RAM(H'50000000-H'53FFFFFF) Clear.... please send ! ('.' & CR stop load) SPI Data Clear(H'FF) Check :H'00000000-0003FFFF Erasing..Erase Completed SAVE SPI-FLASH....... complete!
= Qspi/HyperFlash Save Information ===========[edit]
SpiFlashMemory Stat Address : H'00000000 SpiFlashMemory End Address : H'00000E67
===============================================[edit]
>xls2
Qspi/HyperFlash writing of Gen3 Board Command ========[edit]
Load Program to Spiflash Writes to any of SPI address. Please select,FlashMemory.
1 : QspiFlash (U5 : S25FS128S) 2 : QspiFlash Board (CN2: S25FL512S) 3 : HyperFlash (SiP internal) Select (1-3)>3 READ ID OK.
Program Top Address & Qspi/HyperFlash Save Address
Please Input Program Top Address =======[edit]
Please Input : H'44000000
== Please Input Qspi/HyperFlash Save Address[edit]
Please Input : H'1C0000
Work RAM(H'50000000-H'53FFFFFF) Clear.... please send ! ('.' & CR stop load) Program over size Error
SpiFlashMemory Stat Address : H'001C0000 SpiFlashMemory End Address : H'105C05D3
>xls2
Qspi/HyperFlash writing of Gen3 Board Command ========[edit]
Load Program to Spiflash Writes to any of SPI address. Please select,FlashMemory.
1 : QspiFlash (U5 : S25FS128S) 2 : QspiFlash Board (CN2: S25FL512S) 3 : HyperFlash (SiP internal) Select (1-3)>3 READ ID OK.
Program Top Address & Qspi/HyperFlash Save Address
Please Input Program Top Address =======[edit]
Please Input : H'e6302000
== Please Input Qspi/HyperFlash Save Address[edit]
Please Input : H'40000
Work RAM(H'50000000-H'53FFFFFF) Clear.... please send ! ('.' & CR stop load)
