Thread history

From Talk:R-Car/Boards/Yocto-Gen3
Viewing a history listing
Jump to: navigation, search
Time User Activity Comment
18:57, 18 June 2017 Ygohda (talk | contribs)

New reply created

(Reply to Firmware update hangs)
02:25, 8 June 2017 KarthikShanmugam (talk | contribs)

New reply created

(Reply to Firmware update hangs)
01:38, 6 June 2017 Ygohda (talk | contribs)

New reply created

(Reply to Firmware update hangs)
03:30, 5 June 2017 KarthikShanmugam (talk | contribs)

New reply created

(Reply to Firmware update hangs)
19:39, 4 June 2017 Ygohda (talk | contribs)

New reply created

(Reply to Firmware update hangs)
10:41, 31 May 2017 KarthikShanmugam (talk | contribs)

New thread created

 

I got a new WS1.1 Premier starter kit, tried to build 2.19.0 but the kernel was crashing.

Tried to upgrade the firmware, but it failed to download bl2 srec. Now, it is not even booting into u-boot.

I tried downloading the firmware from windows PC (Teraterm) and Linux (minicom), boot params is getting programmed. I can't program none of the other firmware as given in the instructions.

Either it hangs after sending the file (bl2, bl32, cert), or over size error (uboot)

Any inputs to recover the board is welcome.

10:41, 31 May 2017

Address of bl2 has been chenged from Yocto v2.17.0. Please check the following page. http://elinux.org/R-Car/Boards/H3SK#Flashing_firmware

19:39, 4 June 2017

yeah, following the exact instruction in your link. After downloading the bl2 the mini monitor is stuck.

I see that the board can boot into SCIF download, is it possible recover the board by this route?

03:30, 5 June 2017

I've attached the my log.

H3 SAMPLE LOADER V1.16 2016.10.24                                                          
 CPU   : AArch64 CA57                                                                      
 DRAM  : LPDDR4 DDR3200 DEVICE: QSPI Flash(S25FS128) at 40MHz DMA                          
 BOOT  : Normal Boot                                                                       
 Backup: DDR Cold Boot                                                                     
                                                                                           
 jump to 0xE6330000                                                                        
                                                                                           
H3 MiniMonitor V0.23 2016.10.24                                                            
 Work Memory SystemRAM (H'E6328000-H'E632FFFF)                                             
>                                                                                          
>                                                                                          
>xls2                                                                                      
===== Qspi/HyperFlash writing of Gen3 Board Command =============                          
Load Program to Spiflash                                                                   
Writes to any of SPI address.                                                              
Please select,FlashMemory.                                                                 
   1 : QspiFlash       (U5 : S25FS128S)                                                    
   2 : QspiFlash Board (CN2: S25FL512S)                                                    
   3 : HyperFlash      (SiP internal)                                                      
  Select (1-3)>3                                                                           
 READ ID OK.                                                                               
Program Top Address & Qspi/HyperFlash Save Address                                         
===== Please Input Program Top Address ============                                        
  Please Input : H'e6304000                                                                
                                                                                           
===== Please Input Qspi/HyperFlash Save Address ===                                        
  Please Input : H'40000                                                                   
Work RAM(H'50000000-H'53FFFFFF) Clear....
please send ! ('.' & CR stop load)                                                         
H'00040000-0007FFFF Erasing..Erase Completed 
SAVE SPI-FLASH....... complete!

======= Qspi/HyperFlash Save Information  =================
 SpiFlashMemory Stat Address : H'00040000
 SpiFlashMemory End Address  : H'0005B03B
===========================================================

>

If you don't solve it please attach your log.

01:38, 6 June 2017

Issue is not yet resolved, please see log below.


H3 SAMPLE LOADER V1.17 2016.11.08

CPU   : AArch64 CA57
DRAM  : LPDDR4 DDR3200
DEVICE: QSPI Flash(S25FS128) at 40MHz DMA
BOOT  : Normal Boot
Backup: DDR Cold Boot
jump to 0xE6330000

H3 MiniMonitor V0.24 2016.11.08

Work Memory SystemRAM (H'E6328000-H'E632FFFF)

>xls2

Qspi/HyperFlash writing of Gen3 Board Command ========[edit]

Load Program to Spiflash Writes to any of SPI address. Please select,FlashMemory.

  1 : QspiFlash       (U5 : S25FS128S)
  2 : QspiFlash Board (CN2: S25FL512S)
  3 : HyperFlash      (SiP internal)
 Select (1-3)>3
READ ID OK.

Program Top Address & Qspi/HyperFlash Save Address

Please Input Program Top Address =======[edit]
 Please Input : H'e6320000

== Please Input Qspi/HyperFlash Save Address[edit]

 Please Input : H'0

Work RAM(H'50000000-H'53FFFFFF) Clear.... please send ! ('.' & CR stop load) SPI Data Clear(H'FF) Check :H'00000000-0003FFFF Erasing..Erase Completed SAVE SPI-FLASH....... complete!

= Qspi/HyperFlash Save Information ===========[edit]
SpiFlashMemory Stat Address : H'00000000
SpiFlashMemory End Address  : H'00000E67
===============================================[edit]

>xls2

Qspi/HyperFlash writing of Gen3 Board Command ========[edit]

Load Program to Spiflash Writes to any of SPI address. Please select,FlashMemory.

  1 : QspiFlash       (U5 : S25FS128S)
  2 : QspiFlash Board (CN2: S25FL512S)
  3 : HyperFlash      (SiP internal)
 Select (1-3)>3
READ ID OK.

Program Top Address & Qspi/HyperFlash Save Address

Please Input Program Top Address =======[edit]
 Please Input : H'44000000

== Please Input Qspi/HyperFlash Save Address[edit]

 Please Input : H'1C0000

Work RAM(H'50000000-H'53FFFFFF) Clear.... please send ! ('.' & CR stop load) Program over size Error

SpiFlashMemory Stat Address : H'001C0000
SpiFlashMemory End Address  : H'105C05D3

>xls2

Qspi/HyperFlash writing of Gen3 Board Command ========[edit]

Load Program to Spiflash Writes to any of SPI address. Please select,FlashMemory.

  1 : QspiFlash       (U5 : S25FS128S)
  2 : QspiFlash Board (CN2: S25FL512S)
  3 : HyperFlash      (SiP internal)
 Select (1-3)>3
READ ID OK.

Program Top Address & Qspi/HyperFlash Save Address

Please Input Program Top Address =======[edit]
 Please Input : H'e6302000

== Please Input Qspi/HyperFlash Save Address[edit]

 Please Input : H'40000

Work RAM(H'50000000-H'53FFFFFF) Clear.... please send ! ('.' & CR stop load)

02:25, 8 June 2017

> Please Input : H'e6302000 This is wrong address. e6304000 is correct.

I added a table to the wiki. please check again.

http://elinux.org/R-Car/Boards/H3SK#Flashing_firmware

18:57, 18 June 2017