Firmware update hangs

Jump to: navigation, search

Address of bl2 has been chenged from Yocto v2.17.0. Please check the following page. http://elinux.org/R-Car/Boards/H3SK#Flashing_firmware

18:39, 4 June 2017

yeah, following the exact instruction in your link. After downloading the bl2 the mini monitor is stuck.

I see that the board can boot into SCIF download, is it possible recover the board by this route?

02:30, 5 June 2017

You do not have permission to edit this page, for the following reasons:

  • The action you have requested is limited to users in the group: Users.
  • You must confirm your email address before editing pages. Please set and validate your email address through your user preferences.

You can view and copy the source of this page.

Return to Thread:Talk:R-Car/Boards/Yocto-Gen3/Firmware update hangs/reply (3).

Issue is not yet resolved, please see log below.


H3 SAMPLE LOADER V1.17 2016.11.08

CPU   : AArch64 CA57
DRAM  : LPDDR4 DDR3200
DEVICE: QSPI Flash(S25FS128) at 40MHz DMA
BOOT  : Normal Boot
Backup: DDR Cold Boot
jump to 0xE6330000

H3 MiniMonitor V0.24 2016.11.08

Work Memory SystemRAM (H'E6328000-H'E632FFFF)

>xls2

Qspi/HyperFlash writing of Gen3 Board Command ========[edit]

Load Program to Spiflash Writes to any of SPI address. Please select,FlashMemory.

  1 : QspiFlash       (U5 : S25FS128S)
  2 : QspiFlash Board (CN2: S25FL512S)
  3 : HyperFlash      (SiP internal)
 Select (1-3)>3
READ ID OK.

Program Top Address & Qspi/HyperFlash Save Address

Please Input Program Top Address =======[edit]
 Please Input : H'e6320000

== Please Input Qspi/HyperFlash Save Address[edit]

 Please Input : H'0

Work RAM(H'50000000-H'53FFFFFF) Clear.... please send ! ('.' & CR stop load) SPI Data Clear(H'FF) Check :H'00000000-0003FFFF Erasing..Erase Completed SAVE SPI-FLASH....... complete!

= Qspi/HyperFlash Save Information ===========[edit]
SpiFlashMemory Stat Address : H'00000000
SpiFlashMemory End Address  : H'00000E67
===============================================[edit]

>xls2

Qspi/HyperFlash writing of Gen3 Board Command ========[edit]

Load Program to Spiflash Writes to any of SPI address. Please select,FlashMemory.

  1 : QspiFlash       (U5 : S25FS128S)
  2 : QspiFlash Board (CN2: S25FL512S)
  3 : HyperFlash      (SiP internal)
 Select (1-3)>3
READ ID OK.

Program Top Address & Qspi/HyperFlash Save Address

Please Input Program Top Address =======[edit]
 Please Input : H'44000000

== Please Input Qspi/HyperFlash Save Address[edit]

 Please Input : H'1C0000

Work RAM(H'50000000-H'53FFFFFF) Clear.... please send ! ('.' & CR stop load) Program over size Error

SpiFlashMemory Stat Address : H'001C0000
SpiFlashMemory End Address  : H'105C05D3

>xls2

Qspi/HyperFlash writing of Gen3 Board Command ========[edit]

Load Program to Spiflash Writes to any of SPI address. Please select,FlashMemory.

  1 : QspiFlash       (U5 : S25FS128S)
  2 : QspiFlash Board (CN2: S25FL512S)
  3 : HyperFlash      (SiP internal)
 Select (1-3)>3
READ ID OK.

Program Top Address & Qspi/HyperFlash Save Address

Please Input Program Top Address =======[edit]
 Please Input : H'e6302000

== Please Input Qspi/HyperFlash Save Address[edit]

 Please Input : H'40000

Work RAM(H'50000000-H'53FFFFFF) Clear.... please send ! ('.' & CR stop load)

01:25, 8 June 2017

> Please Input : H'e6302000 This is wrong address. e6304000 is correct.

I added a table to the wiki. please check again.

http://elinux.org/R-Car/Boards/H3SK#Flashing_firmware

17:57, 18 June 2017