Thread history

Fragment of a discussion from Talk:R-Car/Boards/Yocto-Gen3
Viewing a history listing
Jump to: navigation, search
Time User Activity Comment
No results

Address of bl2 has been chenged from Yocto v2.17.0. Please check the following page. http://elinux.org/R-Car/Boards/H3SK#Flashing_firmware

18:39, 4 June 2017

yeah, following the exact instruction in your link. After downloading the bl2 the mini monitor is stuck.

I see that the board can boot into SCIF download, is it possible recover the board by this route?

02:30, 5 June 2017

I've attached the my log.

H3 SAMPLE LOADER V1.16 2016.10.24                                                          
 CPU   : AArch64 CA57                                                                      
 DRAM  : LPDDR4 DDR3200 DEVICE: QSPI Flash(S25FS128) at 40MHz DMA                          
 BOOT  : Normal Boot                                                                       
 Backup: DDR Cold Boot                                                                     
                                                                                           
 jump to 0xE6330000                                                                        
                                                                                           
H3 MiniMonitor V0.23 2016.10.24                                                            
 Work Memory SystemRAM (H'E6328000-H'E632FFFF)                                             
>                                                                                          
>                                                                                          
>xls2                                                                                      
===== Qspi/HyperFlash writing of Gen3 Board Command =============                          
Load Program to Spiflash                                                                   
Writes to any of SPI address.                                                              
Please select,FlashMemory.                                                                 
   1 : QspiFlash       (U5 : S25FS128S)                                                    
   2 : QspiFlash Board (CN2: S25FL512S)                                                    
   3 : HyperFlash      (SiP internal)                                                      
  Select (1-3)>3                                                                           
 READ ID OK.                                                                               
Program Top Address & Qspi/HyperFlash Save Address                                         
===== Please Input Program Top Address ============                                        
  Please Input : H'e6304000                                                                
                                                                                           
===== Please Input Qspi/HyperFlash Save Address ===                                        
  Please Input : H'40000                                                                   
Work RAM(H'50000000-H'53FFFFFF) Clear....
please send ! ('.' & CR stop load)                                                         
H'00040000-0007FFFF Erasing..Erase Completed 
SAVE SPI-FLASH....... complete!

======= Qspi/HyperFlash Save Information  =================
 SpiFlashMemory Stat Address : H'00040000
 SpiFlashMemory End Address  : H'0005B03B
===========================================================

>

If you don't solve it please attach your log.

00:38, 6 June 2017

Issue is not yet resolved, please see log below.


H3 SAMPLE LOADER V1.17 2016.11.08

CPU   : AArch64 CA57
DRAM  : LPDDR4 DDR3200
DEVICE: QSPI Flash(S25FS128) at 40MHz DMA
BOOT  : Normal Boot
Backup: DDR Cold Boot
jump to 0xE6330000

H3 MiniMonitor V0.24 2016.11.08

Work Memory SystemRAM (H'E6328000-H'E632FFFF)

>xls2

Qspi/HyperFlash writing of Gen3 Board Command ========[edit]

Load Program to Spiflash Writes to any of SPI address. Please select,FlashMemory.

  1 : QspiFlash       (U5 : S25FS128S)
  2 : QspiFlash Board (CN2: S25FL512S)
  3 : HyperFlash      (SiP internal)
 Select (1-3)>3
READ ID OK.

Program Top Address & Qspi/HyperFlash Save Address

Please Input Program Top Address =======[edit]
 Please Input : H'e6320000

== Please Input Qspi/HyperFlash Save Address[edit]

 Please Input : H'0

Work RAM(H'50000000-H'53FFFFFF) Clear.... please send ! ('.' & CR stop load) SPI Data Clear(H'FF) Check :H'00000000-0003FFFF Erasing..Erase Completed SAVE SPI-FLASH....... complete!

= Qspi/HyperFlash Save Information ===========[edit]
SpiFlashMemory Stat Address : H'00000000
SpiFlashMemory End Address  : H'00000E67
===============================================[edit]

>xls2

Qspi/HyperFlash writing of Gen3 Board Command ========[edit]

Load Program to Spiflash Writes to any of SPI address. Please select,FlashMemory.

  1 : QspiFlash       (U5 : S25FS128S)
  2 : QspiFlash Board (CN2: S25FL512S)
  3 : HyperFlash      (SiP internal)
 Select (1-3)>3
READ ID OK.

Program Top Address & Qspi/HyperFlash Save Address

Please Input Program Top Address =======[edit]
 Please Input : H'44000000

== Please Input Qspi/HyperFlash Save Address[edit]

 Please Input : H'1C0000

Work RAM(H'50000000-H'53FFFFFF) Clear.... please send ! ('.' & CR stop load) Program over size Error

SpiFlashMemory Stat Address : H'001C0000
SpiFlashMemory End Address  : H'105C05D3

>xls2

Qspi/HyperFlash writing of Gen3 Board Command ========[edit]

Load Program to Spiflash Writes to any of SPI address. Please select,FlashMemory.

  1 : QspiFlash       (U5 : S25FS128S)
  2 : QspiFlash Board (CN2: S25FL512S)
  3 : HyperFlash      (SiP internal)
 Select (1-3)>3
READ ID OK.

Program Top Address & Qspi/HyperFlash Save Address

Please Input Program Top Address =======[edit]
 Please Input : H'e6302000

== Please Input Qspi/HyperFlash Save Address[edit]

 Please Input : H'40000

Work RAM(H'50000000-H'53FFFFFF) Clear.... please send ! ('.' & CR stop load)

01:25, 8 June 2017

> Please Input : H'e6302000 This is wrong address. e6304000 is correct.

I added a table to the wiki. please check again.

http://elinux.org/R-Car/Boards/H3SK#Flashing_firmware

17:57, 18 June 2017